How To Reset Funai Led Thru Service Menu

FUNAI LED 24 -H 9001 G

SERVICE Fashion RESETTING SOFTWARE UPDATE Power SUPPLY CIRCUIT

Service way

How to set up the service mode
1. Turn the power on.
2. Press [Card] button to brandish Setup carte du jour.
3. Select "Software" in "OTHERS" and printing [OK] button.
4. Press [0], [4], [ii], [five], [seven], [4] and [ Data (i) ] buttons on the remote command unit of measurement in this order. The post-obit screen appears.

Purity Check Mode
This mode cycles through full-screen displays of ruddy, green, blue, and white to check for not-active pixels.
1. Enter the Service mode.
2. Each time the [seven] button on the remote command unit is pressed, the display changes

3. To cancel or to exit from the Purity Bank check Mode, press [BACK] push button.

White Balance Adjustment
Purpose: To mix red and blue beams correctly for pure white.
Symptom of Misadjustment: White becomes bluish or reddish.

ane. Operate the unit for more than 60 minutes.
ii. Gear up the color analyzer at the CHROMA manner and zero indicate calibration. Bring the optical receptor pointing at the center of the LCD-Console.

Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
3. Enter the Service way.
4. Printing [ Volume Down ] button iii times on the remote control unit to select "Drive setting" mode. "Drive" appears on the screen.
5. Press [3] button to select the "HDB" for High Drive Blue adjustment. ("HDB" appears on the screen.)

6. Press [Menu] button. The internal Raster signal appears on the screen. ("Internal (Unmarried)" appears on the upper correct of the screen.

7. Printing [P UP / Down ] buttons to adjust the color temperature becomes 12000°Chiliad (x= 0.272 / y= 0.278 ±0.002).
viii. Printing [1] button to select the "HDR" for High Drive Ruby adjustment ("HDR" appears on the screen.) and press [P UP / DOWN ] buttons to adjust the color temperature.
nine. If necessary, adjust the "HDB" or "HDR" over again.
10. Press [6] button to select the "LDB" for Depression Drive Blue adjustment ("LDB" appears on the screen.) and press [P Up / Downward ] buttons to adjust the color temperature.

11. Press [four] push to select the "LDR" for Low Drive Carmine adjustment ("LDR" appears on the screen.) and press [P Upwards/Downward ] buttons to suit the colour temperature.
12. If necessary, conform the "LDB" or "LDR" over again.
13. Printing [Back] button to enter the Service mode again.
xiv. Printing [ Information (i) ] button on the remote control unit to shift to the self check mode screen. If "WB OK" is displayed, this adjustment completes.
If "WB NG" is displayed, turn the Air conditioning switch (on the lower left of the back of the unit) off and on. And then repeat above steps from 3. to thirteen. Check the cocky check mode screen again. If "WB NG" is displayed, replace the LCD Panel or Digital Main CBA.
15. To abolish or to go out from the White Residue Adjustment, press [BACK] push button.

INITIALIZE THE LCD TELEVISION
How to initialize the LCD television set:
one. Turn the ability on.
2. Enter the service mode.
- To cancel the service fashion, press [POWER ] button on the remote control unit.
three. Printing [ Data (i)] push button on the remote control unit to initialize the LCD television.
4. Later confirming that "INITIALIZED : OK" appears on the screen, turn the AC switch (on the lower left of the dorsum of the unit) off.

Firmware Update Process
Check the electric current version
ane. Press [Carte du jour] button on the remote control unit to display the menu mode.
2. Printing [Up] or [DOWN] to select "Others", then printing [OK] button.
3. Press [UP] or [DOWN] to select "Software", and so press [OK] button.
The current FW version will be displayed.

Preparation
i. Prepare USB storage device.
2. Copy F/Westward-file (pkg file) to USB storage device.
Notation: Brand sure to utilize the bare USB Storage.
3. Rename the F/W-file's name to "upgrade.pkg".

Update procedure
ane. Turn the AC switch (on the lower left of the back of the unit) off.
2. Insert USB storage device with F/Due west to Tv set.
iii. Turn the Ac switch on.
4. Updating starts automatically. Red LED flashes.
Note: Practise not plow off the Boob tube and do not remove the USB storage device while this procedure.
five. When updating is completed, the Tv set will turn back on automatically.
6. To shift the Tv gear up to standby way, press [ POWER ] button on the remote command unit.
7. Remove USB storage device from Idiot box set.
eight. Press [ Power ] button again to plow the power on.
9. Press [MENU] button on the remote command unit to display the carte du jour mode.
10. Select "Parental" - "Pin CODE:".
11. Press [4], [7], [3] and [7] buttons on the remote command unit.
12. Select "Factory Reset" and press [OK] button.

Ability SUPPLY CIRCUIT

CLICK ON THE IMAGE TO ZOOM IN